Yaskawa YASNAC PC NC Maintenance Manual Manuale Utente Pagina 244
- Pagina / 301
- Indice
- RISOLUZIONE PROBLEMI
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
Chapter 8: Fixed File Operations PC NC Maintenance Manual
8-42
28. Click the Next button.
29. The Destination drive, which is ‘Free Space’, is shown.
30. Ensure the check box is checked and click the Next button.
31. If the Resize Option pop-up menu is visible, select the option
‘Leave remaining free space’, then click OK.
32. Set the Disk Write Mode to ‘Fast’.
33. When the final confirmation data is shown, click the Finish but-
ton.
34. Restoration of the image begins. This process takes a few min-
utes.
35. Pop up the result of image restoration. If there is an error, try
again. If the error is persistent, a defective hard disk may be the
cause.
36. Click No to view the result.
37. Go back to the main menu. Click the Exit button to close the
Drive Image window.
38. Click the Reboot button. Do not take out the Drive Image floppy
disk.
- YASNAC PC NC 1
- Maintenance Manual 1
- Contents 2
- Electrical Connection 4
- PC NC case 5
- Connection Between Devices 6
- Connector Layout NC Side 7
- NAC JZNC-JFC10 board 7
- 1.2 General Specifications 8
- All dimensions in millimeters 9
- 246 10
- 6 x 4.16 10
- Table 1.3: Heat Generation 12
- 2.1 Routine Inspection 14
- 2.2 Battery 14
- 2.3 Servo Motor 16
- 2.5 Touch Screen 18
- 2.6 Control Panel 19
- Chapter 4: Troubleshooting 22
- Troubleshooting (1) 25
- Table 4.11: Jog Feedrate 42
- Deceleration switch signal 46
- (*DCX signal) 46
- Figure 4.2: Spindle Rotation 49
- During boot up of the PC NC 53
- 01:Overcurrent 56
- 05: Overload 57
- 11:Output overvoltage 57
- 12:Power circuit low voltage 58
- F0:ROM is defective 62
- F1:EEPROM is defective 62
- F5:CPU is defective 63
- .. : Control card fault 63
- AL-01:Overcurrent 68
- AL-02:Ground fault 69
- AL-31:Motor overspeed 75
- AL-33:The load is abnormal 76
- AL-60:Tuning incompletion 80
- AL-65:INC signal error 83
- AL-A4:YENET1200 card error 3 87
- AL-F0:ROM is defective 92
- AL-F2:EEPROM is defective 2 93
- AL-F3:EEPROM is defective 3 93
- AL-F4:EEPROM is defective 4 93
- The motor does not rotate 95
- The motor reverses 96
- The motor does not stop 97
- Cause and measures 100
- The VS-626M5 101
- Operation 103
- Operation Of Digital Operator 104
- Maintenance and Inspection 105
- 4.3 Receiving 107
- 2 7P5 5 E * 108
- Upper and Lower Covers Opened 109
- 4.4 Installation 111
- Heat Sink 112
- (a) Front View (b) Side View 112
- (a) Front View 113
- (b) Side View 113
- 4.5 Wiring 114
- AC Reactor (L) (Note) 115
- P1N1 Power Cable 116
- A general-purpose noise 119
- Figure 4.14: Grounding 122
- 7. Main Circuit Configuration 125
- 8. Parts Required for Wiring 129
- 9. Control Signal Connectors 135
- Wiring The Control Circuit 137
- 1. Control Signals 137
- 51CN 5CN, 52CN 143
- 3CN (Option) 144
- (a) 0V Common 146
- (b) +24V Common 146
- (c) External Common 146
- 4.6 Operation 149
- (a)@Flange-mounted Type 150
- (b)@Foot-mounted Type 150
- Run Command 151
- (Fault occurrence No.) 152
- 4.7 Digital Operator 154
- RUN STOP 156
- Note: “—” is not displayed 157
- Numbers Letters 157
- 65432 10 158
- Display Example 166
- 626M5 and the VS-656MR5 168
- 4.9 Troubleshooting 170
- Fault Cause Corrective Action 177
- Chapter 5: Adjustments 181
- Location Explanation 182
- 6.1 CPU Rack 183
- 6.2 CRT Display Unit 190
- 6.3 Floppy Disk Drive Unit 199
- 6.4 NC Power Supply 200
- 6.6 Noise Filter 202
- Chapter 7: Memory Option 203
- 8.1 NC Data Handling 205
- Restore Kit Contents 235
- 1. External CD ROM Drive 235
- • EXP computer, INC CD-865 235
- 26. Click the Next button 243
- 7. Touch the Close button 250
- 10. Touch the Start button 253
- Common Instructions 254
- Next button 254
- Yes button to agree 255
- 8.4 CNC Card Software Update 274
- ON < 275
- 8.5 Manual Page Customization 284
Prodotti e manuali riguardandi Apparecchiature Yaskawa YASNAC PC NC Maintenance Manual
Apparecchiature Yaskawa MotionSuite Series Machine Controller Programming Manuale Utente
(187 pagine)
(187 pagine)
Apparecchiature Yaskawa MotionSuite Series Machine Controller Software Man Manuale Utente
(461 pagine)
(461 pagine)
Apparecchiature Yaskawa MP2600iec Manuale Utente
(50 pagine)
(50 pagine)
Apparecchiature Yaskawa YTerm Manuale Utente
(56 pagine)
(56 pagine)
Apparecchiature Yaskawa LEGEND-MC Manuale Utente
(360 pagine)
(360 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale